Best Phobya products in the Water cooling connection accessories category

On this page you'll find a ranking of the best Phobya products in this category. To give you a quick overview, we've already ranked the most important information about the products for you.

1. Phobya Extension G1/4 to G1/4 knurled MSV

The extension from G1/4" male thread to G1/4" female thread is used to extend the threaded connection and thus allows angled connections to be used more universally. The hose can thus be routed in the same direction, as the angled connections are now on top of each other. Technical details: color: nickel-plated brass length without thread: 10.7mm thread length: 4mm Scope of delivery: 1x extension G1/4 to G1/4 nickel-plated knurled - MSV Note: This knurled adapter is supplied incl. seal. 

2. Phobya G1/4' Pressure relief valve MSV

This pressure relief valve can, for example, be simply screwed into a T-piece and thus be installed at any point in the circuit. Some expansion tanks offer several openings where standard caps are used, the valve can be used here. The 1/4" thread connection is also very short, only 4mm, and allows many other mounting points in your water cooling. The low complete height of the valve, without thread of 16mm, also speaks for the wide range of applications. The seal on the underside provides additional security to keep your system sealed. The valve allows excess pressures of 0.3-0.4kg/cm² to escape at 4.3-5.7psi. 

3. Phobya Noise Destructor V.1 for pump decoupling

The variety of assembly possibilities is a completely new development step by the Phobya company. The two fixed mats are covered with adhesive tape on both sides. For easy decoupling, remove all 4 protective foils and glue everything together and the decoupling is ready. As an alternative, if you are often on the road with your case, for example, you can also screw the Phobya Noise Destructor tight. A hole has been pre-punched for almost every pump. With the article 52010 from our product range, the pump is screwed on tightly once again and a further noise-absorbing element has been integrated. These holes can also be used for the bottom side to screw the opposite side tightly.

Pump compatibility (pre-punched retaining holes):
among others Laing DDC, Laing D5, Eheim 1046 (HPPS, Aquastream, Watercool 12V), Eheim 1048, Magicool 12V, Phobya DC 260 & DC 400, EK-DCP 2.2 & DCP 4.0

We recommend to order as useful accessories for example article number: 52010 or 52007 and/or suitable mounting bolts & nuts.

This product has been tested for you:
Overclocking station 

4. Phobya Radiator sealing tape 5mm for 120mm fan

This sealing tape is provided with an adhesive tape on one side and is stuck to the component of its choice. Now the fan can be placed with its outer edge on the sealing strip and when the fan screws are tightened, the strip compresses, if necessary, to less than 1mm and compensates for unevenness and gaps between the component and the fan. This way the air has no chance to escape and the effect of the fans is increased once again!

The sealing tape has already been perfectly cut to fit the corresponding fan sizes, so that this simply has to be stuck to the radiator and the fans have to be screwed tight! 

5. Phobya Extension G1/4 to G1/4 rotatable silver nickel-plated

The extension from G1/4" male thread to G1/4" female thread is used to extend the thread connection and thus allows angled connections to be used more universally.
The hose can thus be guided in the same direction, as the elbow connections are now on top of each other.

Technical details:
Colour: silver nickel-plated
thread: 1/4" outside to 1/4" inside
Thread length: 4mm
Length: 20mmScope of delivery:
1x Phobya extension G1/4 to G1/4 rotatable - silver nickel plated 

6. Phobya Hose clamp Allen 16-17mm

Note: If you use the hose clamps with hose nozzles, please note that the outer diameter of the hoses is increased by 1-2mm depending on the wall thickness.

7. Phobya Eheim 1046/48 inlet and 1250 outlet adapter to G1/4' gerä

With the G 1/4" adapter for the Eheim 1046/48 it is possible to use connections with G1/4" external thread. The adapter is simply screwed into the front of the pump and can be used if an expansion tank is not required. It has an O-ring seal.(3/8" to 1/4" adapter) Technical details: Material: Brass, gold-plated Thread size: 1/4 inch Scope of delivery: Pump adapter knurled with long-life sealing ring Please note: Do not screw in the adapter "dry", otherwise the O-ring will torsion and then leak. Therefore, moisten the O-ring before screwing it in, then there will be no problems. Note: Over tightening the pump adapter can cause the plastic trim to break. By resting the O-ring and a slight twisting motion by hand, the tightness is already guaranteed. 

8. Phobya Hose clamp strip 13mm (10x1,5mm) 6-fold, (140 x 20 x 20mm )

For clean laying of hose. The hose is simply inserted into the clip. Create order in your PC. You can either glue the clamping units (hot glue, double-sided adhesive tape), or fix them over the small hole, e.g. with an M3 screw or wire. The bar consists of 6 clips that can be used individually or together. 

9. Phobya Universal pumps mounting base (Eheim, Magicool, Lai

This pump base made of aluminum not only enables very simple and quick installation of the pump, but also significantly dampens the vibrations of the pump. Resonances with PC housings can thus be effectively reduced or even completely eliminated. The pump is firmly screwed to the aluminum base using the decouplers provided. The aluminum base can then be mounted in the PC case, e.g. on the floor, using the special Velcro mat, which has very strong adhesive on both sides. This 3-fold technology guarantees the best possible decoupling. The decoupling buffers reduce the vibrations, the aluminum base absorbs the remaining vibrations and the Velcro tape prevents the transfer of any residual vibrations to the case. Technical details: Dimensions(LxWxH): 90x 80x 12mm Material: aluminum silver anodized Compatible with the following pumps: Phobya DC12-220/260/400 (adhesive mat) Eheim 1046 (u.HPPS, Aquastream, etc.) Magicool universal pump 12V Laing DDC-1T (u. 1T Plus, 1RT, 1RT Plus) Scope of delivery: Alusockel Velcro mat Mounting material This product has been tested for you: Coolingtechnique (it) . 

10. Phobya Radiator sealing tape 10mm for 140mm fan

Sealing tape for optimum fan mounting on radiators or with housings.

In order to increase the efficiency of its fans on the radiators or its water cooling, Phobya has again developed an innovative product, which makes its complete system run even more efficiently with little cost and effort! A certain percentage of the air flow always escapes, because the fan does not lie tightly on the frame of the radiator or the housing. In order to minimize exactly this loss, this sealing tape is now available!

This sealing tape is provided with an adhesive tape on one side and is stuck to the component of its choice. Now the fan can be placed with its outer edge on the sealing tape and when the fan screws are tightened, the strip compresses, if necessary, to less than 1mm and evens out unevenness and gaps between the component and the fan. This way the air has no chance to escape and the effect of the fan is increased even more!

The sealing tape has already been perfectly cut to fit the corresponding fan sizes, so this simply needs to be stuck onto the radiator and the fans screwed tight!

Technical details:

Material: fine foam
Colour: grey
Suitable for : 140 mm fan
Thickness: 10 mm (compressible under pressure under 2 mm)
width: 6 mm

Scope of delivery:

1x Phobya radiator sealing tape 10 mm for 140 mm fan 

See all products