EUR269,37
Ergotron Hx
Table, 49"
Questions about Ergotron Hx
What would you like to know?
0 questions and answers
Helpful answer
Basically, such monitor mounts must support the weight and possibly the height of the monitor alone. Size specifications such as -42" here, for example, should be regarded more as guidelines. The mount here is attached/screwed to the tabletop with two clamps (see Fig. 4) or can also be permanently mounted by means of a hole directly through the tabletop. Instructions: https://www.ergotron.com/portals/0/reserved/resources/3e1f0d4bb999407ebc471fbfecbe6554-orig.pdf
Helpful answer
Unfortunately, we cannot obtain this variant from any of our suppliers :(
Hello, I couldn't answer you but it works perfectly with my Samsung UltraWide 49 inch
Galaxus
8 months ago
Helpful answer
The "HX Arm With Very Heavy Duty Pivot Desk Mount Black" from Ergotron is compatible with various monitors, regardless of whether they are curved or not. - Max. Monitor size: The mount supports monitors up to a size of 57 inches. - VESA wall mount type: The mount is compatible with 100 x 100 mm and 75 x 75 mm VESA mounts. - Payload: The mount can support a load of up to 17 kg. Since the Gigabyte AORUS FO32U2P has a size of 32 inches and probably fulfils the VESA mounting requirements, it should be compatible with this mount, provided it uses the appropriate VESA mounting holes and does not exceed the weight limit.
Automatically generated from the .
Helpful answer
It should work, the fixing is standard.
Hi Bernd, I measured the distance of my HX monitor arm from the table top to the lower edge of the VESA mount - at maximum "extended" height. It is 32.5 cm. In my opinion, this will unfortunately not be enough. :-(
You need this part: Samsung Wall Bracket You should have already received it with the monitor.
Helpful answer
Not suitable for 57 inch. Horizontal bracket is too weak for the projection of the 57 inch. Always tilts down. Had to make special adjustment to keep it horizontal. The extension arms are strong enough.
Helpful answer
I have the ASUS ROG Strix XG49VQ on it and it works perfectly. If that helps.
Helpful answer
Firstly, you need to check that the vesa standards are the same (100x100 200x200). If this is not the case, you will need to buy an adaptive plate to make it compatible. If they are the same then try to check if there are screws on the screen that allow you to remove the round part and uncover the fixing plate (this is often the case with competing brands). If neither of the two solutions work, it will be complicated. Good evening
It doesn't matter. I wouldn't choose the monitor based on the mount, rather the other way around. Just look at the VESA size.
I assume that it is only the module for the monitor.
The arm is very stable, I have the Samsung Neo G9 in 49". The table was bought at Ikea and is a fake wooden table (5cm thick). I have never fully extended the arm but I don't think it should be a problem. The mounting plate of the Ergotron is quite large compared to others. The money is worth it, I have already bought it twice because it convinced me so much.
Helpful answer
Hi Tim, I have two Samsung 49 LC49HG90DMRXEN directly above each other in use. I had to search for a long time and finally decided on the "Neomounts by Newstar FPMA-D960DVBLACKPLUS". Please note that you will need the wall brackets supplied with the monitors to mount them BN96-42913B BN61-14898B Samsung Monitor Wall Bracket (No. 324686683974). I have to admit that this solution is not optimal either and aligning the two monitors so that it fits was quite tricky, especially with a weight of 15 kg per monitor. But it worked and the mount is stable and serves the purpose.
Yes there is, but unfortunately not at Digitec.
I can't find any information on this, but normally it should be ok :)
I cannot answer this exactly, but the spring can be adjusted. However, I would clarify exactly at what weight this arm is still suitable. It is perfect for my Samsung 49". However, since this is a "right hummer" in size and weight, I don't think that much lighter ones work well.
As far as I can remember, no wall-mounting components were included. I would advise you to look for another product that is designed for this.
Helpful answer
the holder is fixed with a clamp. the table remains intact.
Helpful answer
Hello The plate itself is "only" 6cm, the 2 plates on the screws are 8cm. So the whole bracket protrudes 8cm into it. However, you could make the tabletop "thicker" with a wooden board/block, and thus stretch it on the wooden board/block and the metal frame. According to the instructions, the bracket can be attached to a table with up to 66mm. Best regards
Afaik no difference. Reference is made to the same manufacturer's number.
You cannot mount two monitors with this arm, but he is able to reach on top, so if you have two of the Arms this would work. Maybe this one would give you the possibility to mount two arms with the same mount point.
Yes, definitely, because of the weight, otherwise it slouches forward.
Is this stand ok for the LG 38WN95C-W curved monitor or do you need another stand to fix on a table?
Helpful answer
Depending on the characteristics of your monitor and stand yes they are compatible. :)
Helpful answer
PureMounts PM-ADAPT-B (adapter / mounting plates) I have mounted the same TV on the same arm
30 of 58 questions