1

I currently have a 49 inch monitor. Now I would like to upgrade my setup a little. I now have 2 questions. Should I buy a second 49 inch monitor and "stack" both or should I buy 2x27 inch monitors and hang them above my 49 inch? Now I need a recommendation for which setup I should choose (if anyone here already has experience) and suitable monitor mounts. I have a standing desk, so only a desk-mounted mount is an option. Thanks for the tips and suggestions

  2

But isn't there a vesa adapter for 45" HP curved monitors on the market?

  1

Hi all - I am looking for a monitor mount that can be attached to a USM Haller table. Any ideas?

  5

I have a standing desk where the tabletop is only 80cm deep. This means that the screen is almost too close for my taste. For this reason, I am looking for a monitor arm with which it is possible to position the screen further back than the desk top - I hope you understand what I mean. I would prefer to have a distance of 90cm instead of 80cm and ideally there should be two screens. Anyone have a screen mount recommendation? Thank you

  2

So that I can mount my 27" & 34" monitor horizontally, 27" at the bottom & 34" at the top, but can also reverse the whole thing effortlessly without having to do much remounting, i.e. 34" at the bottom & 27" at the top, I am looking for a mount on which the arm or the gas spring can be adjusted in height by 40cm. Is there such a thing? Am I the only one who has this usecase? :S

  0

  1

Hello everyone, I am looking for a suitable mount for my 42" LG OLED monitor (approx. 10 kg). It would be important that the mount can be attached to an electrically height-adjustable standing table (table thickness approx. 2-3 cm). Alternatively, I would also be interested in an electrically adjustable mount, but I suspect that these tend to be in the higher price range. Does anyone have any recommendations or experience with similar setups? Many thanks for any tips! :)

  0

Hi, I'm looking for a monitor arm with a base no wider than 5cm. I've bought a "Team7 Pisa" desk with a courtesy panel and the space between the two panels doesn't allow me to install a monitor arm with a wider base. In the worst case I'd get monitors with 'normal' feet but I want to make sure I've explored all the options. Any ideas? Thanks!

  1

  0

  0

I am currently trying to find a solution for attaching a touchscreen to a table. It should be as height-adjustable and tiltable as possible. The obvious solution is to use a monitor arm. But now I'm wondering whether the mount is stable enough to withstand the pressure of touch or whether the screen will simply move away. I would be very grateful if someone could try this out, and would be open to any other ideas. Many thanks in advance!

  1

  0

Hello together Can anyone recommend a monitor mount for a USM Haller table? Many thanks!

  0

  1

Dear Community, I am looking for a monitor mount for on the table (wall is plaster and does not hold any weight). It is important that the mount is very high, as a 37 inch monitor should go OVER the G9 49 inch! Unfortunately, there is no filter for this and there is no height specified on the mounts themselves, or at least I haven't found one yet. Thanks for any tips

  1

Most dual monitor mounts extend backwards far beyond the edge of the table if you want the maximum adjustment possibilities. What if my table is adjacent to a wall and I can't afford to pull the monitors far forward? Can I then throw the idea of dual mounts overboard and have to switch to two single mounts or am I seeing a problem where there is none?

  0

I'm looking for a stand that will fit on my desk but as the edge of the desk underneath the table is at an angle my current stand slips and is not reliable at all for my monitors, does anyone have a recommendation for a stand that will reach far enough under the desk?

  4

  0

  1

Good day I am looking for a wall bracket with a joint load capacity of 8kg. that can be locked. The reason for this is vibrations on the boat Can you help me?

  0

Good day... I have the following problem. I am looking for a monitor stand for 2 screens. The lower one would be a 34 inch (curved, approx. 11.1kg) and the upper one a 27 inch (approx. 6kg). The monitors should be on top of each other due to lack of space. Both have Vesa 100x100. The whole thing should be without a clamp, but with a stand. I hope you can help me. Thanks a lot

  2

I have been looking for an alternative to one stand per screen for several months now and would like to have the same stand for my 3 32" screens. I can't find any other solution than a totally external stand fixed to the floor. I would like to be able to put it on my desk and have my 3 screens perfectly aligned.

  1

  12

  0

Does anyone know if there is an overview of the product suggestions on the start page with reduced prices? Often there is a product with a price and "You have added this product to your watchlist for CHF xyz.-" underneath. But they disappear again and then another one appears, so if I want to see the previous one again, I can't find it anywhere :)

  1

  4

I am looking for a monitor mount for a 27" Dell screen that on the one hand is as flat as possible, but on the other hand allows the screen to be pulled far forward. I have a table flush against a wall at the back and want the screen as close to the wall as possible for working, but for racing sims I have a chair with a steering wheel and I want to pull the screen as close to me as possible. Is there anything?

  1

hey guys i am looking for a monitor mount for three screens but i want 2 on the bottom and one on the top maybe someone can help me thanks

  1

Hi all, I am looking for a tall monitor mount for a 24 inch display. The goal would be to have the display stacked above my 34 inch ultrawide monitor. So I need either a 2nd singke monitor mount or a monitor mount for the 2 monitors.

  4